published in the Magazine World Coal, March 2017 Issue
mine has its own geological condition. As such, requirements of
individual mines vary and pump system designs must be adapted as
necessary to meet country-specific regulations. Pump stations are the
heart of the longwall operation in underground mining. High pressure
pumps generate the necessary pressure for the roof supports in the
longwall. Furthermore, the pump stations enable the roof supports to
move along the face of the coal seam. The necessary performance in terms
of litres and pressure is fundamentally dependent on the rate of
excavation and the supporting power required by the roof supports.
Currently, in high-capacity longwall applications, flow rates of up to
1270 l/min at an average of 340 bar are required.
Water-spray pump stations are used to minimise dust formation in the longwall. The station's plunger pumps supply the shearer water-spray, or the coal plow water-spray and the cooling systems of the drive motors with the necessary pressure and volumetric flow rates. The pumps in the water-spray stations typically deliver 600 l/min at 90 bar.
today offers far more than just high-pressure pumps and pump stations
for the mining industry. Since the late 1980s, the company has expanded
into the field of water hydraulics.
A close collaboration has also taken place with Caterpillar Global Mining Europe GmbH in Lünen, Germany (then operating under the name Bucyrus), jointly looking for a solution to significantly improve the water quality in an underground longwall in a Polish mine. At the time, Caterpillar was in the process of implementing a complete longwall in the mine, but was concerned about the durability of the hydraulics props, because of the extremely high concentrations of salt in the water. As a result, an extensive water analysis of the mixing water was prepared. It is well known that salt, or salty water, accelerates corrosion. In technical facilities, the term corrosion refers to the reaction of a metallic material with its environment, which causes a measurable change in the material and which can result in the impairment of the function of a metallic component or of an entire system.
Experience has shown that this is not the only mine with such contaminated water and that it has already led to problems in longwall operations.
collaboration with Caterpillar, Hauhinco developed a solution for this
problem and tested it on its own test-bench. By means of a reverse
osmosis unit, it was possible to successfully filter out the salt
content and other substances identified within the mixing water; a quick
and simple solution for the problem had thus been found. However, for
the next stage, it was necessary to develop this into a system approved
for underground mining. Alongside the standard mining requirements, the
system needs to be suitable for the hard conditions in underground
mining and it also needs to be able to supply the required flow rate of
cleaned water for the longwall. After less than five months, the result
was a high-performance water treatment unit with all the necessary
approvals for underground mining.
The system is installed in a compact base frame with the dimensions 3300mm x 1519mm x 1100mm and can be simply integrated into an overall system, irrespective of the manufacturer. Therefore, a subsequent upgrade of an existing high pressure station is also possible and an immediate improvement in water quality can be achieved. Particularly in completely new systems a water treatment system is a logical and reasonable investment. Cavitation problems in the props of the roof supports can be prevented from the very start, lifecycle costs are reduced and the investments of the mine are protected.
integral components of the water treatment system are the filtration
unit, the reverse osmosis unit, the tank and the control system.
In the first stage of the water treatment process, the raw water, (i.e. the untreated water from the mine) enters a multi-stage filter. During the filtration process, first the solids contained in the raw water are filtered out using a double filter at 50µm and 25µm and then by a 5µm fine filter.In the next step, the water enters the key element of the system: the reverse osmosis unit. In the standard system design, this unit consists of one pressure pipe with a membrane, a metering pump, a dispersant tank, two flow monitors and a needle valve. For pressure monitoring purposes, there are also two pressure gauges installed in the raw water feed pipe and in the concentrate drain of this assembly. A metering pump mixes the raw water with a dispersant mixture and pumps it through the pressure pipe. The membrane separates the raw water into permeate, i.e. purified process water and concentrate, i.e. waste water. Optimally, the ratio of permeate to concentrate should be 1:1. This ratio is set by means of the two flow monitors and the needle valve. The standard system design includes an integrated 1000L tank for storing the process water. The tank size can of course be adapted to the requirements of the mine. To monitor the filling level, the tank is equipped with an electrical level monitoring system and a visual filling level display. The dispersant tank has a volume of 400L and is likewise equipped with an electrical level monitoring system and a visual filling level display.
The operating modes "automatic operation" and "test operation" are pre-programmed in the control system. "Automatic operation" allows the fully automatic treatment of the raw water and the delivery of the process water from the tank to the pump station. In "test operation", the various components of the water treatment system can be individually activated and deactivated.
first water treatment system was put into operation in 2010. From
2000l/h of salty raw water, it was possible to prepare 1000l/h of clean
water. The raw water had a conductivity of 1990 µS. After the treatment
process, the value for the clean process water was just 19.5 µS. These
values show the effectiveness of the system. The system itself runs
fully automatic in the treatment process, i.e. no manual operation is
required. The degree of contamination of the filters is displayed. The
maintenance-friendly structure allows fast, cost-effective and simple
replacement of the filter elements. Even after five years of underground
operation, the system still runs flawlessly and supplies the roof
supports with clean medium.
Franz-Heinrich Suilmann, Head of Engineering for Roof Support Hydraulics at Caterpillar Global Mining Europe GmbH, sees the preparation of the emulsion for the longwall hydraulics by a water treatment system based on reverse osmosis as a practical alternative. Thus corrosion damages in the hydraulic systems can be avoided and ensuring sustained compliance with Caterpillar's quality requirements for the hydraulic fluid.
Mines, where the water quality already led to problems in the hydraulic props in the longwall quickly showed interest in the ability to treat the water directly underground. Since the launch, Hauhinco has already commissioned a number of systems in coal mines. The system has also been continually developed since its launch and adapted to the increasing requirements and respective circumstances. In addition to high salt content, the water samples from the mines also contained high levels of chalk, iron and many other solids. These substances can also be filtered out, in some cases with adaptations within a system.Because of the increasing requirements in terms of the volumes of water required in the longwall, several variants of the treatment system have already been developed over recent years. The tank sizes and the treatment volumes can now be flexibly adapted to the requirements. The largest system designed so far has eight membranes and can supply up to 8000l/h of water.
In underground mining, a water treatment
system is a logical and reasonable addition to a longwall hydraulic
system. The aim of every mine is to achieve the most effective
operation, while keeping lifecycle costs as low as possible. The compact
design of the water treatment system and the manufacturer-independent
and problem-free integration into a pressure supply station can be a
fundamental component in achieving this objective. Compared with the
overall costs of a longwall, the additional investment is small and,
considering the lifecycle costs and the service life of roof supports,
it pays off.